Devices You Need to Install a New Bathtub

Details Here

We've come across the article about How to Install a Bathtub below on the web and accepted it made good sense to write about it with you on this page.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, as well as often, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough job. If the old bathtub is conveniently obtainable, the project can move immediately; if you have to open a wall to eliminate the old bathtub as well as place the brand-new bathtub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will need a helper to leave the old bathtub and also set in the new one. Ensure you have certified on your own for the work and also are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is much better to think about using one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This article will help you set up a new tub in your restroom if you have already purchased a new tub as well as don't need to alter the arrangement of your previous supply of water pipes.
Your tools and product list must consist of the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Removing Old Touches


    If you require to change old taps with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, activate the faucets to drain any type of water remaining in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted access that is usually the instance.
    Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will originate from the pipelines. When the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
    Before carrying on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.

    Fitting New Touches


    If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipelines.
    If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet and the sink. Safeguard the tap in position with the producer given backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The previous type needs to be connected to the faucet finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.

    Installing the Tub


    Utilizing both wooden boards under its feet, position the tub in the called for position. The wooden boards are practical in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
    The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the tub till the spirit level checks out degree.
    To mount taps, fit the bottom of the furthest adaptable faucet connector to the suitable supply pipeline by making a compression sign up with; then do the same for the other faucet.
    Activate the water supply and inspect all joints and also brand-new pipework for leakages and tighten them if required. Fill up the bath tub as well as also check the overflow outlet as well as the typical electrical outlet for leakages.
    Ultimately, fix the bath paneling as explained in the producer's user's manual. Tiling and also securing around the bath tub should wait until the bathtub has been utilized a minimum of once as this will certainly resolve it right into its last position.

    Preparing for the Setup


    First of all, the supporting framework supplied with the bathroom must be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to stop stress on the tub.
    Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washers.
    Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final placement.

    Tiling Around the Tub


    In the area where the bathroom satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, causing the water to pass through the wall between the bathroom and the tiling, bring about issues with dampness and also possible leaks to the ceiling listed below.
    You can choose from a selection of coloured sealants to assimilate your fixtures and installations. They are sold in tubes and also cartridges, as well as can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before securing, to allow for the motion experienced when the tub remains in usage. The sealant can fracture relatively very early if you do not consider this activity before securing.
    Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water resistant glue and also grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Installing A Bathtub

    Do you like more info about A Step-by-Step Guide to Installing a Bathtub? Leave feedback directly below. We will be interested to see your thinking about this post. In hopes that you come back again before long. Feel free to take the time to distribute this page if you enjoyed reading it. Thanks so much for going through it.




    Hire A Pro


    Leave a Reply

    Your email address will not be published. Required fields are marked *